Bearings One Way Clutch Categories
Bearings - One Way - Sprag - Standard
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
Designed for press fit installation. Correct interference dimensions must be maintained to obtain maximum bearing and clutch performance. Mount the clutch ensuring that the shaft drive directionis in the direction indicated by the arrow on the inner race. To install, use a press tool / do not hammer or apply other stock to clutch. Make sure housing has enough strength to withstand press required for fitting installation. High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes.
Related Information:
There is also a good range of Bearings - One Way - Sprag - Standard on the Small Parts and Bearings website.
Bearings - One Way - Roller
Roller Clutch Bearings rotate in one direction only.
Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.
Related Information:
There is also a good range of Bearings - One Way - Roller on the Small Parts and Bearings website.
You may also be interested in
Bearings Clutch
Lazy Susan Bearings
One unit construction for maximum stability and quiet running. Used to make light weight turntables.
Centre opening allows for a centre post if required.
Related Information:
There is also a good range of Lazy Susan Bearings on the Small Parts and Bearings website.
Bearings - Roller - Cylindrical - NF Series - Removable Outer Ring
Outer ring is removable in one direction
Bearings - Roller - Cylindrical - NJ Series - Removable Inner Ring
Inner ring is removable in one direction and shouldered on the opposite side
Bearings - Roller - Cylindrical - NUP Series - Removable Inner Ring
Inner ring is removable in one direction with supporting shoulder washer
Bass One Shimano Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
There is also a good range of Bass One Shimano Parts on the Small Parts and Bearings website.
Bearings - Thrust - Ball - Grooved - Chrome Steel
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Related Information:
There is also a good range of Bearings - Thrust - Ball - Grooved - Chrome Steel on the Small Parts and Bearings website.
Bearings - Thrust - Ball - Grooved - Stainless Steel
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Related Information:
There is also a good range of Bearings - Thrust - Ball - Grooved - Stainless Steel on the Small Parts and Bearings website.
Bearings - Thrust - Ball - Flat - Chrome Steel
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Related Information:
There is also a good range of Bearings - Thrust - Ball - Flat - Chrome Steel on the Small Parts and Bearings website.
Bearings - Thrust - Ball - Flat - Stainless Steel
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Related Information:
There is also a good range of Bearings - Thrust - Ball - Flat - Stainless Steel on the Small Parts and Bearings website.
Bearings - Ball - Ceramic Hybrid
Steel Races with Si3N4 Ceramic Balls
Bearings with steel races and ceramic balls. For standard bearings, the balls are usually one of the first components to show wear. Ceramic balls are harder than steel and do not wear as easily. Items with high speed cages have the suffixes T9H, TNH, TW or KC.
Related Information:
There is also a good range of Bearings - Ball - Ceramic Hybrid on the Small Parts and Bearings website.
Bearings - Thrust - Ball - Grooved - ZRO2 Ceramic
3 Piece Thrust Bearings Open Type. Excellent performance in electrical and magnetism sensitive applications. Full ceramic silicon nitride.
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Related Information:
There is also a good range of Bearings - Thrust - Ball - Grooved - ZRO2 Ceramic on the Small Parts and Bearings website.
Bearings - Chamfered Edges
Chamfered edge bearings for Linear Guide Systems and pushbikes
Often used in pushbike headsets. Note bearings for pushbikes with two chamfered edges have the chamfer on the inner ring on one side and outer ring on the other - designation CEP.
Related Information:
There is also a good range of Bearings - Chamfered Edges on the Small Parts and Bearings website.
Bearings - Thrust - Ball - Grooved - Si3N4 Ceramic
3 Piece Thrust Bearings Open Type. Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02. Full ceramic silicon nitride.
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics.
Related Information:
There is also a good range of Bearings - Thrust - Ball - Grooved - Si3N4 Ceramic on the Small Parts and Bearings website.
Rail Supports - With Shaft - One Piece
One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.
Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments.
Related Information:
There is also a good range of Rail Supports - With Shaft - One Piece on the Small Parts and Bearings website.
Bearings - Tapered Roller - Cone
Replacements for existing tapered roller cones (inner part). Match with part number on your existing bearing. It is recommended that you change both cup and cone whenever possible.
There is also a good range of Bearings - Tapered Roller - Cone on the Small Parts and Bearings website.
Linear - Mini Rail - Self-Lubricating - Carriage and Rail
Comes with one carriage. Spare carriages sold separately - match by rail width.
Low profile self-lubricating linear guide system with one piece carriage design. Excellent alternative to linear ball bearing systems. Precision series made from RC70 ceramic coated rail with self lubricating Frelon Gold. Dampens vibration and tolerates shock loads. Will not rust. No metal to metal contact. No balls or rolling elements to trap contamination, skid or damage rail. Operation is consistent, smooth and quiet. Maintenance free. Used in packaging machines, medical equipment, wash-down and harsh environments.
Related Information:
There is also a good range of Linear - Mini Rail - Self-Lubricating - Carriage and Rail on the Small Parts and Bearings website.
Linear - Mini Rail - Self-Lubricating - Carriage
Additional carriages for the Mini-Rail system. Match by rail width.
Low profile self-lubricating linear guide system with one piece carriage design. Excellent alternative to linear ball bearing systems. Precision series made from RC70 ceramic coated rail with self lubricating Frelon Gold. Dampens vibration and tolerates shock loads. Will not rust. No metal to metal contact. No balls or rolling elements to trap contamination, skid or damage rail. Operation is consistent, smooth and quiet. Maintenance free. Used in packaging machines, medical equipment, wash-down and harsh environments.
Related Information:
There is also a good range of Linear - Mini Rail - Self-Lubricating - Carriage on the Small Parts and Bearings website.
Bearings - Peek - Single Row - with Glass Balls
PEEK (Polyetheretherketone), is a high temperature, high-performance engineering polymer.
Races made from PEEK - Balls made from 316 Stainless Steel - Cages from PEEK. PEEK offers chemical and water resistance similar to PPS (Polyphenylene Sulfide) but can operate at higher temperatures. PEEK can be used continuously to 338 Deg F (170 Deg C) and in hot water or steam without permanent loss in physical properties. Wear, Chemical & Hydrolysis Resistant. Exceptional performance over a wide range of temperatures and extreme conditions. Low Smoke and Toxic Gas Emission.
Related Information:
There is also a good range of Bearings - Peek - Single Row - with Glass Balls on the Small Parts and Bearings website.
Linear Slides - Cross Roller Tables - Aluminium
Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.
Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.
There is also a good range of Linear Slides - Cross Roller Tables - Aluminium on the Small Parts and Bearings website.
Linear Slides - Cross Roller Tables - Steel
Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.
Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.
There is also a good range of Linear Slides - Cross Roller Tables - Steel on the Small Parts and Bearings website.
EM3000 Nose Cone C. De Giorgi Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
There is also a good range of EM3000 Nose Cone C. De Giorgi Parts on the Small Parts and Bearings website.
Bearings - Peek - Single Row - with 316 Stainless Steel Balls
PEEK (Polyetheretherketone), is a high temperature, high-performance engineering polymer.
Races made from PEEK - Balls made from Ground Glass - Cages from PEEK. PEEK offers chemical and water resistance similar to PPS (Polyphenylene Sulfide) but can operate at higher temperatures. PEEK can be used continuously to 338 Deg F (170 Deg C) and in hot water or steam without permanent loss in physical properties. Wear, Chemical & Hydrolysis Resistant. Exceptional performance over a wide range of temperatures and extreme conditions. Low Smoke and Toxic Gas Emission.
Related Information:
There is also a good range of Bearings - Peek - Single Row - with 316 Stainless Steel Balls on the Small Parts and Bearings website.
Linear Slides - Low Profile - Crossed Roller Table - Aluminium
Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.
Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.
There is also a good range of Linear Slides - Low Profile - Crossed Roller Table - Aluminium on the Small Parts and Bearings website.
Linear Slides - Low Profile - Crossed Roller Table - Stainless Steel
Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.
Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.
There is also a good range of Linear Slides - Low Profile - Crossed Roller Table - Stainless Steel on the Small Parts and Bearings website.
Rollers - Durasoft - Shaft Mount - With Ball Bearing
Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.
Designed for use in machines and assembly operations where part movement and protection is needed. Durasoft rollers have a gentle but firm touch. Unique shape of holes adds to their soft but resilient nature. Blue colour may turn a shade of green when exposed to UV lighting.
There is also a good range of Rollers - Durasoft - Shaft Mount - With Ball Bearing on the Small Parts and Bearings website.
Bearings - Ball - Angular Contact - 440C Stainless
Including miniature sizes down to 8mm from stock and even smaller available.
Single row angular contact ball bearings.
Related Information:
There is also a good range of Bearings - Ball - Angular Contact - 440C Stainless on the Small Parts and Bearings website.
Bearings - Ball - Angular Contact - Chrome Steel
Including miniature sizes down to 8mm from stock and even smaller available.
Single row angular contact ball bearings.
Related Information:
There is also a good range of Bearings - Ball - Angular Contact - Chrome Steel on the Small Parts and Bearings website.
Bearings - Ball - Angular Contact - Flanged - 440C Stainless
Single row angular contact ball bearings with flanges.
Related Information:
There is also a good range of Bearings - Ball - Angular Contact - Flanged - 440C Stainless on the Small Parts and Bearings website.
Bearings - Ceramic Si3N4 - Angular Contact
Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02. Full ceramic silicon nitride.
Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls and rings. HRC80 Hardness. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage. Up to 700 deg C without a cage or seals.
Related Information:
There is also a good range of Bearings - Ceramic Si3N4 - Angular Contact on the Small Parts and Bearings website.
Bearings - Ceramic Si3N4 - Radial
Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02. Full ceramic silicon nitride.
Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls and rings. HRC80 Hardness. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage. Up to 700 deg C without a cage or seals.
Related Information:
There is also a good range of Bearings - Ceramic Si3N4 - Radial on the Small Parts and Bearings website.
Bearings - Ceramic ZRO2- Angular Contact
Excellent performance in electrical and magnetism sensitive applications. Full ceramic zirconia.
Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage. Up to 1000 deg C without a cage or seals.
Related Information:
There is also a good range of Bearings - Ceramic ZRO2- Angular Contact on the Small Parts and Bearings website.
Bearings - Ceramic ZrO2 - Radial
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed. Full ceramic zirconia.
Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage. Up to 1000 deg C without a cage or seals.
Related Information:
There is also a good range of Bearings - Ceramic ZrO2 - Radial on the Small Parts and Bearings website.
Bearings - Ceramic ZrO2 - Self Aligning - Double Row
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed. Full ceramic zirconia.
Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls and rings. Si3N4 available to special order. High and low temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage. Up to 1000 deg C without a cage or seals.
Related Information:
There is also a good range of Bearings - Ceramic ZrO2 - Self Aligning - Double Row on the Small Parts and Bearings website.
Bearings - Conveyor - Hex Bore - Plastic - Double Row
Plastic hex bore conveyor bearings with 316 stainless balls
Loads and Speeds are for reference only. Testing recommended.
There is also a good range of Bearings - Conveyor - Hex Bore - Plastic - Double Row on the Small Parts and Bearings website.
Bearings - Conveyor - Hex Bore - Plastic - Single Row
Plastic hex bore conveyor bearings with 316 stainless balls
Loads and Speeds are for reference only. Testing recommended.
There is also a good range of Bearings - Conveyor - Hex Bore - Plastic - Single Row on the Small Parts and Bearings website.
Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row
316 stainless conveyor bearings with plastic cage and plastic hex insert
Loads and Speeds are for reference only. Testing recommended.
There is also a good range of Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row on the Small Parts and Bearings website.
Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row
316 stainless conveyor bearings with plastic cage and plastic hex insert
Loads and Speeds are for reference only. Testing recommended.
There is also a good range of Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row on the Small Parts and Bearings website.
Bearings - Roller - Cylindrical - N Series - Removable Outer Ring
Outer ring is removable in both directions
Bearings - Roller - Cylindrical - NU Series - Removable Inner Ring
Inner ring is removable in both directions
Bearings - Ball - Double Row - Angular Contact - Chrome Steel
Double Row Ball Bearings - Angular Contact.
Related Information:
There is also a good range of Bearings - Ball - Double Row - Angular Contact - Chrome Steel on the Small Parts and Bearings website.
Bearings - Ball - Double Row - Angular Contact - Stainless Steel
Double Row Ball Bearings - Angular Contact.
Related Information:
There is also a good range of Bearings - Ball - Double Row - Angular Contact - Stainless Steel on the Small Parts and Bearings website.
Bearings - Ball - Double Row - Radial - Chrome Steel
Related Information:
There is also a good range of Bearings - Ball - Double Row - Radial - Chrome Steel on the Small Parts and Bearings website.
Main Pages
About Us
Balls List
Bearings List
Brands
Catalogue
Ceramic Bearings List
Contact Us
Dental Bearings
Downloadable PDF Catalogue Balls
Downloadable PDF Catalogue Ceramic Bearings
Downloadable PDF Catalogue Corrosion Resistant Bearings
Downloadable PDF Catalogue Disc Springs
Downloadable PDF Catalogue Economy Bearings
Downloadable PDF Catalogue High Speed Bearings
Downloadable PDF Catalogue Metallic Bushes
Downloadable PDF Catalogue Plastic Bearings
Downloadable PDF Catalogue Sintered Bronze Bushes
Downloadable PDF Catalogue Snap Rings
Downloadable PDF Catalogue Solid Bronze Bushes
Downloadable PDF Catalogue Standard Ball Bearing Range
Downloadable PDF Catalogue Super Precision Bearings
Downloadable PDF Catalogue Thrust Bearings
Downloadable PDF Cross Reference ADR and SKF
Downloadable PDF Cross Reference Barden Bearings
Downloadable PDF Cross Reference Flocast
Downloadable PDF Cross Reference McMaster Carr
Downloadable PDF Cross Reference Miniature Precison Bearings
Downloadable PDF Cross Reference NSK and NTN
Downloadable PDF Cross Reference Reid Supply
Downloadable PDF Cross Reference SDP-SI Designatronics
Downloadable PDF Cross Reference Sintered Bronze
Freight Rates and Shipping Times
Frequently Asked Questions
Google Search
Hobby Clearance
Hobby Information
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Satellite Reaction Wheels
Shipping Rates and Times
Small Bearings
Technical
Terms
5 Axis Machine Tool Bearings
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414) - Trading as Bearing Shop Online
Bearing Shop Online offers 28836 products in 493 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Bearing Shop Online is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Bearing Shop Online 1997. All rights reserved.
