Bearings Stainless Special Grades Categories
Bearings - Ball - AISI304 Stainless Steel
Corrosion and Heat resistance - Non Magnetic - Non Hardenable. Quality Japanese manufacture.
Tolerances differ from standard bearing types - see below. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. ID +0.05 / -0 mm , OD +0 / -0.03 mm up to 10mm bore, Width +0/- 0.12 mm. Mid range speed and load between 304 stainless and 440C stainless. Rubber seals are Nitrile but fluorine rubber may be available on request. Cages, balls, races and shields from AISI 304 Stainless Steel.
Related Information:
Bearings - Ball - Anti Corrosion - Special Stainless
Higher corrosion resistance than 440C stainless - HRC59 Hardness - Same or higher load than 440C
Ideal for applications with salt spray or chemicals in the pH range 3 to 12. ISC CASSTOP design with special TBN-6H stainless steel. Other sizes available on request.
Related Information:
There is also a good range of Bearings - Ball - Anti Corrosion - Special Stainless on the Small Parts and Bearings website.
Bearings - Ball - 17-4PH Stainless Steel
Excellent Corrosion and Heat resistance - Hardness is between 300 grades and 400 grades. SUS630 grade.
Standard bearing tolerances. Low load, low speed applications requiring maximum corrosion resistance. Rubber seals are Nitrile but fluorine rubber may be available on request. Cages and shields from AISI 304 Stainless Steel. Balls and races from SUS630 (17-4PH) Stainless Steel.
Related Information:
Bearings - Ball - 316 Stainless Steel - Double Row - Open
Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance.
Related Information:
There is also a good range of Bearings - Ball - 316 Stainless Steel - Double Row - Open on the Small Parts and Bearings website.
Bearings - Ball - 316 Stainless Steel - Single Row - Open
Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance.
Related Information:
There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Open on the Small Parts and Bearings website.
Bearings - Ball - 316 Stainless Steel - Single Row - Sealed
Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Sealed on the Small Parts and Bearings website.
Bearings - Ball - 316 Stainless Steel - Single Row - Shielded
Marine, food and medical grade Stainless Steel - Non Hardenable. 316 stainless steel shields.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Stainless steel 316 cage, grade 200 type 316 stainless balls, 316 stainless races, 316 stainless steel shields. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Shielded on the Small Parts and Bearings website.
You may also be interested in
Shafting Precision Ground
Shafting - Ground - Precision - Stainless 416 Grade Hardened
Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.
Related Information:
There is also a good range of Shafting - Ground - Precision - Stainless 416 Grade Hardened on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 420 Grade Hardened
Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.
Related Information:
There is also a good range of Shafting - Ground - Precision - Stainless 420 Grade Hardened on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 440C Grade Hardened
Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.
Related Information:
There is also a good range of Shafting - Ground - Precision - Stainless 440C Grade Hardened on the Small Parts and Bearings website.
Bearings Housings
Housings - Bearing - Pillow Block - Miniature
Spyraflo aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings. Double shielded bearings to minimise contamination.
Related Information:
There is also a good range of Housings - Bearing - Pillow Block - Miniature on the Small Parts and Bearings website.
Bearings Mounted
Bearings - Self Clinching - Self Aligning - Stainless and Delrin -tm-
Spyraflo acetal bearings in a special stainless steel self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information. +/- 5% Static Alignment. See animation link at bottom of web page. Panel material no harder than RB65/RB75. Panel hole to be punched or machined to size A (+0.07/-0.00mm).
Related Information:
There is also a good range of Bearings - Self Clinching - Self Aligning - Stainless and Delrin -tm- on the Small Parts and Bearings website.
Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
There is also a good range of Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings on the Small Parts and Bearings website.
Bearings - Acetal with Stainless Balls - For Plastic Housings
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
There is also a good range of Bearings - Acetal with Stainless Balls - For Plastic Housings on the Small Parts and Bearings website.
Bearings - Ball - 440C Stainless
Also see combined categories:
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
Stainless steel radial ball bearings
Standard single row radial ball bearings. Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore.
Related Information:
There is also a good range of Bearings - Ball - 440C Stainless on the Small Parts and Bearings website.
Bearings - Linear - Ball - Stainless Steel - Closed
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.
Related Information:
There is also a good range of Bearings - Linear - Ball - Stainless Steel - Closed on the Small Parts and Bearings website.
Bearings - Linear - Sliding - Stainless - PTFE - Closed
Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.
There is also a good range of Bearings - Linear - Sliding - Stainless - PTFE - Closed on the Small Parts and Bearings website.
Bearings - Linear - Sliding - Stainless - PTFE - Open
Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.
There is also a good range of Bearings - Linear - Sliding - Stainless - PTFE - Open on the Small Parts and Bearings website.
Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row
316 stainless conveyor bearings with plastic cage and plastic hex insert
Loads and Speeds are for reference only. Testing recommended.
There is also a good range of Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row on the Small Parts and Bearings website.
Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row
316 stainless conveyor bearings with plastic cage and plastic hex insert
Loads and Speeds are for reference only. Testing recommended.
There is also a good range of Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row on the Small Parts and Bearings website.
Bearings - Ball - Flanged - 440C Stainless
Stainless Steel Bearings with Flanges.
Single row radial ball bearings with flanges. Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore.
Related Information:
There is also a good range of Bearings - Ball - Flanged - 440C Stainless on the Small Parts and Bearings website.
Bearings - Ball - WIR - 440C Stainless
Stainless Steel Bearings with a Snap Ring on the OD
Single row radial ball bearings with extended inner ring (wide inner ring). Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore.
Related Information:
There is also a good range of Bearings - Ball - WIR - 440C Stainless on the Small Parts and Bearings website.
Bearings - Thrust - Ball - Flat - Stainless Steel
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Related Information:
There is also a good range of Bearings - Thrust - Ball - Flat - Stainless Steel on the Small Parts and Bearings website.
Bearings - Thrust - Ball - Grooved - Stainless Steel
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Related Information:
There is also a good range of Bearings - Thrust - Ball - Grooved - Stainless Steel on the Small Parts and Bearings website.
Bearings - Ball - Angular Contact - 440C Stainless
Including miniature sizes down to 8mm from stock and even smaller available.
Single row angular contact ball bearings.
Related Information:
There is also a good range of Bearings - Ball - Angular Contact - 440C Stainless on the Small Parts and Bearings website.
Bearings - Ball - Flanged - WIR - 440C Stainless
Stainless Steel Bearings with Flanges.
Single row radial ball bearings with flanges and extended inner rings (wide inner rings). Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore.
Related Information:
There is also a good range of Bearings - Ball - Flanged - WIR - 440C Stainless on the Small Parts and Bearings website.
Bearings - Ball - High Precision - 440C Stainless
Also see combined categories:
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
Stainless Steel Bearings - Abec 5 and Abec 7.
Single row radial ball bearings. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
There is also a good range of Bearings - Ball - High Precision - 440C Stainless on the Small Parts and Bearings website.
Bearings - Thrust - Ball - Washers Only - Stainless Steel
Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.
Stainless Steel Washers are hardened to HRC38.42.
Related Information:
There is also a good range of Bearings - Thrust - Ball - Washers Only - Stainless Steel on the Small Parts and Bearings website.
Bearings - Acetal - Double Row - with 316 Stainless Steel Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.
Related Information:
There is also a good range of Bearings - Acetal - Double Row - with 316 Stainless Steel Balls on the Small Parts and Bearings website.
Bearings - Acetal - Single Row - with 302 Stainless Steel Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 302 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.
Related Information:
There is also a good range of Bearings - Acetal - Single Row - with 302 Stainless Steel Balls on the Small Parts and Bearings website.
Bearings - Acetal - Single Row - with 316 Stainless Steel Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.
Related Information:
There is also a good range of Bearings - Acetal - Single Row - with 316 Stainless Steel Balls on the Small Parts and Bearings website.
Bearings - Ball - Angular Contact - Flanged - 440C Stainless
Single row angular contact ball bearings with flanges.
Related Information:
There is also a good range of Bearings - Ball - Angular Contact - Flanged - 440C Stainless on the Small Parts and Bearings website.
Bearings - Ball - Double Row - Angular Contact - Stainless Steel
Double Row Ball Bearings - Angular Contact.
Related Information:
There is also a good range of Bearings - Ball - Double Row - Angular Contact - Stainless Steel on the Small Parts and Bearings website.
Bearings - Ball - Flanged - High Precision - 440C Stainless
Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.
Single row radial ball bearings with flanges. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
There is also a good range of Bearings - Ball - Flanged - High Precision - 440C Stainless on the Small Parts and Bearings website.
Bearings - Ball - WIR - High Precision - 440C Stainless
Stainless Steel Bearings - Abec 5 and Abec 7.
Single row radial ball bearings with extended inner ring (wide inner ring). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
There is also a good range of Bearings - Ball - WIR - High Precision - 440C Stainless on the Small Parts and Bearings website.
Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless
Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.
Single row radial ball bearings with flanges and extended inner rings (wide inner rings). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
There is also a good range of Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless on the Small Parts and Bearings website.
Dual Vee - Tracks with Mounting Holes - Stainless Steel
Vee guide rails for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
Related Information:
There is also a good range of Dual Vee - Tracks with Mounting Holes - Stainless Steel on the Small Parts and Bearings website.
Dual Vee - Tracks without Mounting Holes - Stainless Steel
Vee guide rails for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
Related Information:
There is also a good range of Dual Vee - Tracks without Mounting Holes - Stainless Steel on the Small Parts and Bearings website.
Bearings - Conveyor - Hex Bore - Plastic - Double Row
Plastic hex bore conveyor bearings with 316 stainless balls
Loads and Speeds are for reference only. Testing recommended.
There is also a good range of Bearings - Conveyor - Hex Bore - Plastic - Double Row on the Small Parts and Bearings website.
Bearings - Conveyor - Hex Bore - Plastic - Single Row
Plastic hex bore conveyor bearings with 316 stainless balls
Loads and Speeds are for reference only. Testing recommended.
There is also a good range of Bearings - Conveyor - Hex Bore - Plastic - Single Row on the Small Parts and Bearings website.
Ball Transfer Units - Flange Mount - Standard - Stainless - Deep
Single ball bearings units for conveyor systems
There is also a good range of Ball Transfer Units - Flange Mount - Standard - Stainless - Deep on the Small Parts and Bearings website.
Ball Transfer Units - Flange Mount - Standard - Stainless - Slim
Single ball bearings units for conveyor systems
There is also a good range of Ball Transfer Units - Flange Mount - Standard - Stainless - Slim on the Small Parts and Bearings website.
Housings - Pillow Block - Washdown
Also see combined categories:
All Spyraflo Pillow Block Mounted Bearings
All Spyraflo Mounted Bearings
All Spyraflo Pillow Block Mounted Bearings
All Spyraflo Mounted Bearings
Spyraflo electroless nickel plated aluminium housing with stainless steel coated self aligning acetal bearings.
See links at bottom of web page for more information. +/- 5% Static Alignment. Electroless nickel plated aluminium housing. Corrosion Resistant. Light weight.
Related Information:
There is also a good range of Housings - Pillow Block - Washdown on the Small Parts and Bearings website.
Ball Transfer Units - Flange Mount - Heavy Duty - Stainless Steel
Single ball bearings units for conveyor systems
There is also a good range of Ball Transfer Units - Flange Mount - Heavy Duty - Stainless Steel on the Small Parts and Bearings website.
Bearings - Acetal - Special Purpose
Special acetal bearings for Bicycle Chain Derailer and special effects lighting systems
There is also a good range of Bearings - Acetal - Special Purpose on the Small Parts and Bearings website.
Bearings - Acetal - Special Types
Light duty acetal bearings used for drawer runners, light duty tracks, garage doors and more.
See descriptions for special features. Not all items are listed in this category. Please contact us if you have a similar type bearing with different dimensions.
There is also a good range of Bearings - Acetal - Special Types on the Small Parts and Bearings website.
Bearings - Polypropylene - Special Types
Polypropylene is for special chemical compatibility usages. Please refer to a compatibility chart.
See descriptions for special features. Not all items are listed in this category. Please contact us if you have a similar type bearing with different dimensions.
There is also a good range of Bearings - Polypropylene - Special Types on the Small Parts and Bearings website.
Bearings - Chamfered Edges
Chamfered edge bearings for Linear Guide Systems and pushbikes
Often used in pushbike headsets. Note bearings for pushbikes with two chamfered edges have the chamfer on the inner ring on one side and outer ring on the other - designation CEP.
Related Information:
There is also a good range of Bearings - Chamfered Edges on the Small Parts and Bearings website.
Bearings - Spherical OD
Bearings with a spherical outside diameter.
Combined listing of spherical OD track rollers and bearings for Linear Guide systems.
Related Information:
There is also a good range of Bearings - Spherical OD on the Small Parts and Bearings website.
Shafting - Pre Drilled and Tapped - Stainless Steel Steel
For use with rail supports and open linear bearings
There is also a good range of Shafting - Pre Drilled and Tapped - Stainless Steel Steel on the Small Parts and Bearings website.
Main Pages
About Us
Balls List
Bearings List
Brands
Catalogue
Ceramic Bearings List
Clearance Items List
Contact Us
Dental Bearings
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Small Bearings
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414) - Trading as Bearing Shop Online
Bearing Shop Online offers 25852 products in 532 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Bearing Shop Online is part of MBA Group offering a select range from the MBA Group catalogue.
Bearing Shop Online products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Bearing Shop Online 1997. All rights reserved.
