Bearings Stainless Special Grades Categories
Bearings - Ball - AISI304 Stainless Steel
Corrosion and Heat resistance - Non Magnetic - Non Hardenable. Quality Japanese manufacture.
Tolerances differ from standard bearing types - see below. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. ID +0.05 / -0 mm , OD +0 / -0.03 mm up to 10mm bore, Width +0/- 0.12 mm. Mid range speed and load between 304 stainless and 440C stainless. Rubber seals are Nitrile but fluorine rubber may be available on request. Cages, balls, races and shields from AISI 304 Stainless Steel.
Related Information:
Bearings - Ball - Anti Corrosion - Special Stainless
Higher corrosion resistance than 440C stainless - HRC59 Hardness - Same or higher load than 440C
Ideal for applications with salt spray or chemicals in the pH range 3 to 12. ISC CASSTOP design with special TBN-6H stainless steel. Other sizes available on request. This category may be available in the new MBA online store at Bearings - Ball - Anti Corrosion - Special Stainless.
Related Information:
There is also a good range of Bearings - Ball - Anti Corrosion - Special Stainless on the Small Parts and Bearings website.
Bearings - Ball - 17-4PH Stainless Steel
Excellent Corrosion and Heat resistance - Hardness is between 300 grades and 400 grades. SUS630 grade.
Standard bearing tolerances. Low load, low speed applications requiring maximum corrosion resistance. Rubber seals are Nitrile but fluorine rubber may be available on request. Cages and shields from AISI 304 Stainless Steel. Balls and races from SUS630 (17-4PH) Stainless Steel.
Related Information:
Bearings - Ball - 316 Stainless Steel - Double Row - Open
Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. This category may be available in the new MBA online store at Bearings - Ball - 316 Stainless Steel - Double Row - Open.
Related Information:
There is also a good range of Bearings - Ball - 316 Stainless Steel - Double Row - Open on the Small Parts and Bearings website.
Bearings - Ball - 316 Stainless Steel - Single Row - Open
Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. This category may be available in the new MBA online store at Bearings - Ball - 316 Stainless Steel - Single Row - Open.
Related Information:
There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Open on the Small Parts and Bearings website.
Bearings - Ball - 316 Stainless Steel - Single Row - Sealed
Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Sealed on the Small Parts and Bearings website.
Bearings - Ball - 316 Stainless Steel - Single Row - Shielded
Marine, food and medical grade Stainless Steel - Non Hardenable. 316 stainless steel shields.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Stainless steel 316 cage, grade 200 type 316 stainless balls, 316 stainless races, 316 stainless steel shields. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Shielded on the Small Parts and Bearings website.
You may also be interested in
Shafting Precision Ground
Shafting - Ground - Precision - Stainless 416 Grade Hardened
Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 416 Grade Hardened.
Related Information:
There is also a good range of Shafting - Ground - Precision - Stainless 416 Grade Hardened on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 420 Grade Hardened
Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 420 Grade Hardened.
Related Information:
There is also a good range of Shafting - Ground - Precision - Stainless 420 Grade Hardened on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 440C Grade Hardened
Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 440C Grade Hardened.
Related Information:
There is also a good range of Shafting - Ground - Precision - Stainless 440C Grade Hardened on the Small Parts and Bearings website.
Housings with Bearing
Housings - Bearing - Pillow Block - Thermoplastic with Stainless Bearing
Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.
Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.
There is also a good range of Housings - Bearing - Pillow Block - Thermoplastic with Stainless Bearing on the Small Parts and Bearings website.
Housings - Bearing - 3 Bolt Offset - Thermoplastic with Stainless Bearing
Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.
Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.
There is also a good range of Housings - Bearing - 3 Bolt Offset - Thermoplastic with Stainless Bearing on the Small Parts and Bearings website.
Housings - Bearing - 4 Bolt Flange - Thermoplastic with Stainless Bearing
Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.
Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.
There is also a good range of Housings - Bearing - 4 Bolt Flange - Thermoplastic with Stainless Bearing on the Small Parts and Bearings website.
Housings - Bearing - Tapped Base - Thermoplastic with Stainless Bearing
Thermoplastic housed units offer a more favourable economic choice. Stainless steel bearings offer a high level of corrosion resistance and all metal parts are made from either 302, 304 or 440C stainless steel.
Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel. Food grade.
There is also a good range of Housings - Bearing - Tapped Base - Thermoplastic with Stainless Bearing on the Small Parts and Bearings website.
Housings - Bearing - Tapped Base Unit - Stainless
Full stainless steel bearing units are the best solution for hostile chemical washdown applications. All metal bearing insert components are a combination of 302, 304 and 440 stainless steel. Seals are silicone rubber. Grease is H-1 food grade.
Operating temperature minus 20 oC to +120 deg C. Solid 304 stainless housings have a machined base and extremely smooth surface finish, essential for demanding washdown installations. These housings do not experience flaking, cracking or discolouration and are virtually unaffected by scrapes. Bearings are removable. Food grade.
There is also a good range of Housings - Bearing - Tapped Base Unit - Stainless on the Small Parts and Bearings website.
Housings - Bearing - 2 Bolt Flange - Thermoplastic with Stainless Bearing
Thermoplastic housed units offer a more favourable economic choice. Stainless steel bearings offer a high level of corrosion resistance and all metal parts are made from either 302, 304 or 440C stainless steel.
Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel. Food Grade.
There is also a good range of Housings - Bearing - 2 Bolt Flange - Thermoplastic with Stainless Bearing on the Small Parts and Bearings website.
Bearings Housings
Housings - Bearing - Pillow Block - Miniature
Spyraflo aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings. Double shielded bearings to minimise contamination. This category may be available in the new MBA online store at Housings - Bearing - Pillow Block - Miniature.
Related Information:
There is also a good range of Housings - Bearing - Pillow Block - Miniature on the Small Parts and Bearings website.
Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
There is also a good range of Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings on the Small Parts and Bearings website.
Bearings - Acetal with Stainless Balls - For Plastic Housings
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended. This category may be available in the new MBA online store at Bearings - Acetal with Stainless Balls - For Plastic Housings.
Related Information:
There is also a good range of Bearings - Acetal with Stainless Balls - For Plastic Housings on the Small Parts and Bearings website.
Bearings - Ball - 440C Stainless
Also see combined categories:
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
Stainless steel radial ball bearings
Standard single row radial ball bearings. Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore. This category may be available in the new MBA online store at Bearings - Ball - 440C Stainless.
Related Information:
There is also a good range of Bearings - Ball - 440C Stainless on the Small Parts and Bearings website.
Bearings - Linear - Ball - Stainless Steel - Closed
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at Bearings - Linear - Ball - Stainless Steel - Closed.
Related Information:
There is also a good range of Bearings - Linear - Ball - Stainless Steel - Closed on the Small Parts and Bearings website.
Bearings - Linear - Sliding - Stainless - PTFE - Closed
Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000. This category may be available in the new MBA online store at Bearings - Linear - Sliding - Stainless - PTFE - Closed.
There is also a good range of Bearings - Linear - Sliding - Stainless - PTFE - Closed on the Small Parts and Bearings website.
Bearings - Linear - Sliding - Stainless - PTFE - Open
Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000. This category may be available in the new MBA online store at Bearings - Linear - Sliding - Stainless - PTFE - Open.
There is also a good range of Bearings - Linear - Sliding - Stainless - PTFE - Open on the Small Parts and Bearings website.
Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row
316 stainless conveyor bearings with plastic cage and plastic hex insert
Loads and Speeds are for reference only. Testing recommended. This category may be available in the new MBA online store at Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row.
There is also a good range of Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row on the Small Parts and Bearings website.
Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row
316 stainless conveyor bearings with plastic cage and plastic hex insert
Loads and Speeds are for reference only. Testing recommended. This category may be available in the new MBA online store at Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row.
There is also a good range of Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row on the Small Parts and Bearings website.
Bearings - Ball - Flanged - 440C Stainless
Stainless Steel Bearings with Flanges.
Single row radial ball bearings with flanges. Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore. This category may be available in the new MBA online store at Bearings - Ball - Flanged - 440C Stainless.
Related Information:
There is also a good range of Bearings - Ball - Flanged - 440C Stainless on the Small Parts and Bearings website.
Bearings - Ball - WIR - 440C Stainless
Stainless Steel Bearings with a Snap Ring on the OD
Single row radial ball bearings with extended inner ring (wide inner ring). Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore. This category may be available in the new MBA online store at Bearings - Ball - WIR - 440C Stainless.
Related Information:
There is also a good range of Bearings - Ball - WIR - 440C Stainless on the Small Parts and Bearings website.
Bearings - Thrust - Ball - Flat - Stainless Steel
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Thrust - Ball - Flat - Stainless Steel.
Related Information:
There is also a good range of Bearings - Thrust - Ball - Flat - Stainless Steel on the Small Parts and Bearings website.
Bearings - Thrust - Ball - Grooved - Stainless Steel
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Thrust - Ball - Grooved - Stainless Steel.
Related Information:
There is also a good range of Bearings - Thrust - Ball - Grooved - Stainless Steel on the Small Parts and Bearings website.
Bearings - Ball - Flanged - WIR - 440C Stainless
Stainless Steel Bearings with Flanges.
Single row radial ball bearings with flanges and extended inner rings (wide inner rings). Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore. This category may be available in the new MBA online store at Bearings - Ball - Flanged - WIR - 440C Stainless.
Related Information:
There is also a good range of Bearings - Ball - Flanged - WIR - 440C Stainless on the Small Parts and Bearings website.
Bearings - Ball - High Precision - 440C Stainless
Also see combined categories:
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
Stainless Steel Bearings - Abec 5 and Abec 7.
Single row radial ball bearings. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Ball - High Precision - 440C Stainless.
Related Information:
There is also a good range of Bearings - Ball - High Precision - 440C Stainless on the Small Parts and Bearings website.
Bearings - Thrust - Ball - Washers Only - Stainless Steel
Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.
Stainless Steel Washers are hardened to HRC38.42. This category may be available in the new MBA online store at Bearings - Thrust - Ball - Washers Only - Stainless Steel.
Related Information:
There is also a good range of Bearings - Thrust - Ball - Washers Only - Stainless Steel on the Small Parts and Bearings website.
Bearings - Ball - Double Row - Angular Contact - Stainless Steel
Double Row Ball Bearings - Angular Contact.
This category may be available in the new MBA online store at Bearings - Ball - Double Row - Angular Contact - Stainless Steel.
Related Information:
There is also a good range of Bearings - Ball - Double Row - Angular Contact - Stainless Steel on the Small Parts and Bearings website.
Bearings - Ball - Flanged - High Precision - 440C Stainless
Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.
Single row radial ball bearings with flanges. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Ball - Flanged - High Precision - 440C Stainless.
Related Information:
There is also a good range of Bearings - Ball - Flanged - High Precision - 440C Stainless on the Small Parts and Bearings website.
Bearings - Acetal - Double Row - with 316 Stainless Steel Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous. This category may be available in the new MBA online store at Bearings - Acetal - Double Row - with 316 Stainless Steel Balls.
Related Information:
There is also a good range of Bearings - Acetal - Double Row - with 316 Stainless Steel Balls on the Small Parts and Bearings website.
Bearings - Acetal - Single Row - with 302 Stainless Steel Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 302 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous. This category may be available in the new MBA online store at Bearings - Acetal - Single Row - with 302 Stainless Steel Balls.
Related Information:
There is also a good range of Bearings - Acetal - Single Row - with 302 Stainless Steel Balls on the Small Parts and Bearings website.
Bearings - Acetal - Single Row - with 316 Stainless Steel Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous. This category may be available in the new MBA online store at Bearings - Acetal - Single Row - with 316 Stainless Steel Balls.
Related Information:
There is also a good range of Bearings - Acetal - Single Row - with 316 Stainless Steel Balls on the Small Parts and Bearings website.
Bearings - Peek - Single Row - with 316 Stainless Steel Balls
PEEK (Polyetheretherketone), is a high temperature, high-performance engineering polymer.
Races made from PEEK - Balls made from Ground Glass - Cages from PEEK. PEEK offers chemical and water resistance similar to PPS (Polyphenylene Sulfide) but can operate at higher temperatures. PEEK can be used continuously to 338 Deg F (170 Deg C) and in hot water or steam without permanent loss in physical properties. Wear, Chemical & Hydrolysis Resistant. Exceptional performance over a wide range of temperatures and extreme conditions. Low Smoke and Toxic Gas Emission.
Related Information:
There is also a good range of Bearings - Peek - Single Row - with 316 Stainless Steel Balls on the Small Parts and Bearings website.
Bearings - PVDF - Single Row - with 316 Stainless Steel Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from PVDF - Balls made from Ground Glass - Cages from PVDF. Kynar -tm- PVDF (Polyvinylidene Fluoride) is a high performance engineering polymer. Kynar -tm- has provided superior chemical resistance properties in critical contact applications for food, pharmaceutical, and semiconductor industries for over 20 years. For chemical and high temperature resistance, low permeability and high mechanical strength. This category may be available in the new MBA online store at Bearings - PVDF - Single Row - with 316 Stainless Steel Balls.
Related Information:
There is also a good range of Bearings - PVDF - Single Row - with 316 Stainless Steel Balls on the Small Parts and Bearings website.
Bearings - Ball - WIR - High Precision - 440C Stainless
Stainless Steel Bearings - Abec 5 and Abec 7.
Single row radial ball bearings with extended inner ring (wide inner ring). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Ball - WIR - High Precision - 440C Stainless.
Related Information:
There is also a good range of Bearings - Ball - WIR - High Precision - 440C Stainless on the Small Parts and Bearings website.
Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless
Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.
Single row radial ball bearings with flanges and extended inner rings (wide inner rings). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless.
Related Information:
There is also a good range of Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless on the Small Parts and Bearings website.
Ball Transfer Units - Screw Stem - Stainless - Precision
Single ball bearings units for conveyor systems
Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at Ball Transfer Units - Screw Stem - Stainless - Precision.
There is also a good range of Ball Transfer Units - Screw Stem - Stainless - Precision on the Small Parts and Bearings website.
Dual Vee - Tracks with Mounting Holes - Stainless Steel
Vee guide rails for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel. This category may be available in the new MBA online store at Dual Vee - Tracks with Mounting Holes - Stainless Steel.
Related Information:
There is also a good range of Dual Vee - Tracks with Mounting Holes - Stainless Steel on the Small Parts and Bearings website.
Bearings - Conveyor - Hex Bore - Plastic - Double Row
Plastic hex bore conveyor bearings with 316 stainless balls
Loads and Speeds are for reference only. Testing recommended. This category may be available in the new MBA online store at Bearings - Conveyor - Hex Bore - Plastic - Double Row.
There is also a good range of Bearings - Conveyor - Hex Bore - Plastic - Double Row on the Small Parts and Bearings website.
Bearings - Conveyor - Hex Bore - Plastic - Single Row
Plastic hex bore conveyor bearings with 316 stainless balls
Loads and Speeds are for reference only. Testing recommended. This category may be available in the new MBA online store at Bearings - Conveyor - Hex Bore - Plastic - Single Row.
There is also a good range of Bearings - Conveyor - Hex Bore - Plastic - Single Row on the Small Parts and Bearings website.
Ball Transfer Units - Flange Mount - Standard - Stainless - Deep
Single ball bearings units for conveyor systems
This category may be available in the new MBA online store at Ball Transfer Units - Flange Mount - Standard - Stainless - Deep.
There is also a good range of Ball Transfer Units - Flange Mount - Standard - Stainless - Deep on the Small Parts and Bearings website.
Ball Transfer Units - Flange Mount - Standard - Stainless - Slim
Single ball bearings units for conveyor systems
This category may be available in the new MBA online store at Ball Transfer Units - Flange Mount - Standard - Stainless - Slim.
There is also a good range of Ball Transfer Units - Flange Mount - Standard - Stainless - Slim on the Small Parts and Bearings website.
Housings - Pillow Block - Washdown
Also see combined categories:
All Spyraflo Pillow Block Mounted Bearings
All Spyraflo Mounted Bearings
All Spyraflo Pillow Block Mounted Bearings
All Spyraflo Mounted Bearings
Spyraflo electroless nickel plated aluminium housing with stainless steel coated self aligning acetal bearings.
See links at bottom of web page for more information. +/- 5% Static Alignment. Electroless nickel plated aluminium housing. Corrosion Resistant. Light weight.
Related Information:
There is also a good range of Housings - Pillow Block - Washdown on the Small Parts and Bearings website.
Ball Transfer Units - Flange Mount - Heavy Duty - Stainless Steel
Single ball bearings units for conveyor systems
There is also a good range of Ball Transfer Units - Flange Mount - Heavy Duty - Stainless Steel on the Small Parts and Bearings website.
Bearings - Acetal - Special Purpose
Special acetal bearings for Bicycle Chain Derailer and special effects lighting systems
This category may be available in the new MBA online store at Bearings - Acetal - Special Purpose.
Related Information:
There is also a good range of Bearings - Acetal - Special Purpose on the Small Parts and Bearings website.
Main Pages
5 Axis Machine Tool Bearings
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Catalogue
Ceramic Bearings List
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Dowel Pins PDF
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Leveling Mounts PDF
Mailorder Form
McMaster Carr Cross Reference PDF
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
Satellite Reaction Wheels
Screws PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414) - Trading as Bearing Shop Online
Bearing Shop Online offers 29942 products in 534 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Bearing Shop Online is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Bearing Shop Online 1997. All rights reserved.
