Shafting No Pictures
Category Matches
Shafting Aluminium
Shafting - Aluminium
Also see combined categories:
All Shafting
All Aluminium Shafting
Drylin aluminium shafting is recommended for use with Igubal Drylin bearings or Frelon lined bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.
There is also a good range of Shafting - Aluminium on the Small Parts and Bearings website.
Shafting - Aluminium - Ceramic Coated
Also see combined categories:
All Shafting
All Aluminium Shafting
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.
There is also a good range of Shafting - Aluminium - Ceramic Coated on the Small Parts and Bearings website.
Shafting - Aluminium - Ceramic Coated - Tapped
Also see combined categories:
All Shafting
All Aluminium Shafting
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.
There is also a good range of Shafting - Aluminium - Ceramic Coated - Tapped on the Small Parts and Bearings website.
Shafting - Pipe - Aluminium
Also see combined categories:
All Pipe Shaft
All Metal Tube
Recommended for use with Igubal Drylin bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and Less than 9.
There is also a good range of Shafting - Pipe - Aluminium on the Small Parts and Bearings website.
Shafting - Supported - Pre-Drilled - Aluminium
Also see combined categories:
All Shafting
All Aluminium Shafting
For Drylin Bearings.
Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and less than 9.
There is also a good range of Shafting - Supported - Pre-Drilled - Aluminium on the Small Parts and Bearings website.
Shafting General Purpose
Shafting - Carbon Steel - Keyed
Also see combined categories:
All Shafting
All Steel Shafting
Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.
Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.
There is also a good range of Shafting - Carbon Steel - Keyed on the Small Parts and Bearings website.
Shafting Precision Ground
Shafting - Ground - Precision - Chrome Plated
Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Case hardened and recommended for use with precision bearings. Ends are not plated.
Case hardened to 60-65 Rockwell C. Chrome plated for corrosion resistance.
There is also a good range of Shafting - Ground - Precision - Chrome Plated on the Small Parts and Bearings website.
Shafting - Ground - Precision - High Carbon Steel
Also see combined categories:
All Shafting
All Steel Shafting
Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.
There is also a good range of Shafting - Ground - Precision - High Carbon Steel on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 303 Grade
Also see combined categories:
All Shafting
All Stainless Shafting
Precision ground shafting.
There is also a good range of Shafting - Ground - Precision - Stainless 303 Grade on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 416 Grade Hardened
Also see combined categories:
All Shafting
All Stainless Shafting
Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.
There is also a good range of Shafting - Ground - Precision - Stainless 416 Grade Hardened on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 420 Grade Hardened
Also see combined categories:
All Shafting
All Stainless Shafting
Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.
There is also a good range of Shafting - Ground - Precision - Stainless 420 Grade Hardened on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 440C Grade Hardened
Also see combined categories:
All Shafting
All Stainless Shafting
Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.
There is also a good range of Shafting - Ground - Precision - Stainless 440C Grade Hardened on the Small Parts and Bearings website.
Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1
Also see combined categories:
All Shafting
All Titanium Shafting
CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.
Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance.
There is also a good range of Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1 on the Small Parts and Bearings website.
Shafting - Ground - Precision - Titanium - Ti-Gr5 - TC4
Also see combined categories:
All Shafting
All Titanium Shafting
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
There is also a good range of Shafting - Ground - Precision - Titanium - Ti-Gr5 - TC4 on the Small Parts and Bearings website.
Shafting - Pre Drilled and Tapped - High Carbon Steel
Also see combined categories:
All Shafting
All Steel Shafting
For use with rail supports and open linear bearings
Straightness: 0.1 mm / mtr.
There is also a good range of Shafting - Pre Drilled and Tapped - High Carbon Steel on the Small Parts and Bearings website.
Shafting - Pre Drilled and Tapped - Stainless Steel Steel
Also see combined categories:
All Shafting
All Stainless Shafting
For use with rail supports and open linear bearings
There is also a good range of Shafting - Pre Drilled and Tapped - Stainless Steel Steel on the Small Parts and Bearings website.
Shafts - Pinion
There is also a good range of Shafts - Pinion on the Small Parts and Bearings website.
Rail Supports - Without Shaft
Also see combined categories:
All Shaft Supports
For mounting of linear shafting.
Shafting sold separately. Support is made from aluminium.
There is also a good range of Rail Supports - Without Shaft on the Small Parts and Bearings website.
Rail Supports - With Shaft
Also see combined categories:
All Shaft Supports
Includes linear shafting.
Includes shaft to h6 tolerances. Support is made from aluminium.
There is also a good range of Rail Supports - With Shaft on the Small Parts and Bearings website.
Shafting General Purpose
Shafts - Flexible - Panel Mount - Cased
Also see combined categories:
All Flexible Panel Mount Shaft
See PDF file at bottom of internet page for Performance Data.
There is also a good range of Shafts - Flexible - Panel Mount - Cased on the Small Parts and Bearings website.
Shafts - Flexible - Panel Mount - Open
Also see combined categories:
All Flexible Panel Mount Shaft
See PDF file at bottom of internet page for Performance Data.
There is also a good range of Shafts - Flexible - Panel Mount - Open on the Small Parts and Bearings website.
Shafting Precision Ground
Rail Supports - With Shaft - One Piece
Also see combined categories:
All Shaft Supports
One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.
Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments.
There is also a good range of Rail Supports - With Shaft - One Piece on the Small Parts and Bearings website.
You may also like
Square Shaft
Shafting - Linear - Square
There is also a good range of Shafting - Linear - Square on the Small Parts and Bearings website.
Assortments
Assortment Kits - Various
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Shim - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
There is also a good range of Assortment Kits - Various on the Small Parts and Bearings website.
Linear Bearings with Housing
Housings - Linear - Square
Also see combined categories:
All Linear Bearing Housings
Used to maintain radial integrity and eliminate the need for parallel shafting.
Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads.
There is also a good range of Housings - Linear - Square on the Small Parts and Bearings website.
Linear Bearings
Bearings - Linear - Ball - Closed
Also see combined categories:
All Closed Linear Ball Bearings
Standard closed type to run on standard 60HRC shafts with h6 tolerances
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.
Bearings - Linear - Ball - Stainless Steel - Closed
Also see combined categories:
All Closed Linear Ball Bearings
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.
There is also a good range of Bearings - Linear - Ball - Stainless Steel - Closed on the Small Parts and Bearings website.
Main Pages
Freight Rates
Terms and Conditions
Privacy Policy
Bearing Shop Online offers 25334 products in 538 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Bearing Shop Online is part of MBA Group offering a select range from the MBA Group catalogue.
Bearing Shop Online products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Bearing Shop Online 1997. All rights reserved.